*rohs directive 2002/95/ec jan 27 2003 including annex specifications are subject to change without notice. customers should verify actual device performance in their specific applications. 6657 - precision potentiometer features bushing mount shaft supported by front sleeve bearing non-standard features and specifications available electrical characteristics 1 standard resistance range....................................................................................1 k to 100 k ohms total resistance tolerance ..................................................................................................... ....10 % independent linearity .......................................................................................................... .........1 % effective electrical angle ..................................................................................................... ..340 3 end voltage .................................................................................................................0.5 % maximum output smoothness .............................................................................................................. .......0.1 % dielectric withstanding voltage (mil-std-202, method 301) sea level .............................................................................................................750 vac m inimum power rating (voltage limited by power dissipation or 300 vac, whichever is less) +70 c ........................................................................................................................ ........1.5 watts +125 c........................................................................................................................ ............0 watt insulation resistance (500 vdc)..................................................................1,000 megohms minimum resolution ................................................................................................................esse ntially infinite environmental characteristics 1 operating temperature range...................................................................................+1 c to +125 c storage temperature range.....................................................................................-65 c to +125 c temperature coefficient over storage temperature range ...........................500 ppm/c maximum vibration ...................................................................................................................... ...................15 g wiper bounce ...........................................................................................0.1 millisecond maximum total resistance shift ..............................................................................................5 % maximu m voltage ratio shift ................................................................................................0.5 % maxim um shock .......................................................................................................................... ...................50 g wiper bounce ...........................................................................................0.1 millisecond maximum total resistance shift ..............................................................................................5 % maximu m voltage ratio shift ................................................................................................0.5 % maxim um load life ............................................................................................................1,000 hour s, 1.5 watts total resistance shift ............................................................................................10 % maximum rotational life (no load) .........................................................................10,000,000 shaft revolutions total resistance shift ............................................................................................10 % maximum moisture resistance (mil-std-202, method 106) total resistance shift ............................................................................................15 % maximum ip rating ...................................................................................................................... ..................ip 40 mechanical characteristics 1 mechanical angle ............................................................................................................... .continuous torque (starting & running) ..............................................................0.40 n-cm (0.5 oz.-in.) maximum mounting.............................................................................170-200 n-cm (15-18 lb.-in.) maximum shaft runout................................................................................................0.025 mm (0.001 in. ) t.i.r. shaft end play ...............................................................................................0.13 mm (0.005 in. ) t.i.r. shaft radial play ...........................................................................................0.13 mm (0.005 in.) t.i.r. backlash ....................................................................................................................... .0.1 maximum weight ......................................................................................................................... .................32 gm terminals...................................................................................................................... .rear turret type soldering condition....................recommended hand soldering using sn95/ag5 no clean solder, 0.025 wire diameter. maximum temperature 399 c (750 f) for 3 seconds. no wash process to be used with no clean flux. marking ................................manufacturers name and part number, resistance value and tolerance, linearity tolerance, wiring diagram, and date code. ganging (multiple section potentiometers) .................................................................1 cup maximum hardware ....................................................one lockwasher (h-37-2) and one mounting nut (h-38-2) is shipped with each potentiometer. recommended part numbers part number* resistance ( ? ) 6657s-1-102 1,000 6657s-1-202 2,000 6657s-1-502 5,000 6657s-1-103 10,000 boldface listings are in stock and readily available through distribution. for other options consult factory. b o u r n s 31 2 30 3 typ. cw clockwise 3/8 "-32 unef-2athd 45 5 x chamfer shaft slot 1 3 cw ccw 2 wiper 1.57 (.062) .38 (.015) 16.46 .38 (.648 .015) 33.34 (1-5/16) dia. 10.317+.000/-.051 (.4062+.000/-.002) dia. shaft 6.345 +.000/-.008 (.2498 +.0000/-.0003) dia. shaft wide 1.19 (.047) x deep 1.60 (.063) r 6.35 (.25) tolerances: except where noted .51 .13 decimals: .xx (.02), .xxx (.005) fractions: 1/64 mm dimensions: (in.) 9.53 .79 (3/8 1/32) 22.23 .79 (7/8 1/32) 3.18 (1/8) 1 at room ambient: +25 ? nominal and 50 % relative humidity, except as noted. product dimensions rev. 06/06 *rohs compliant
|
